Where is the OBD port on a 96 Ford Thunderbird?

Where are OBD ports located?

The most common place to find your car’s OBD2 port is under the dashboard on the driver’s side. Most vehicles have the connector under the instrument panel (aka, the dashboard) on the driver’s side, but some can be found near the center console area or even on the passenger’s side of the car.

Where is the OBD2 port on a Volvo?

Volvo On-Board Diagnostic (OBD) port, also known as OBD-II or OBD 2, is located under the dashboard on the driver’s side.

Where is the OBD port on an Audi?

Where is the OBD2 port on an Audi? In most 1996 and newer Audi vehicles, the OBD2 port is located under the dashboard on the driver’s side, to the steering column’s left. Audi On-Board Diagnostic II (OBD-II) is used to diagnose vehicle problems.

Where is the OBD port on Mercedes?

Where to find the OBD2 port, when trying to connect a scanner to your Mercedes-Benz. The OBD II port is located under the dashboard, driver’s side. Look under the dash, over by the brake pedal.

Where do I connect OBD scanner?

Where is the OBD port on a Audi Q5?

OBD connector location for Audi Q5 (8R) (2008 – 2017)
  1. The OBD2 port is located above the pedals.
  2. The socket is above the brake pedal.
  3. The OBD2 diagnostics port.

Where do you plug in code reader Audi A4?

OBD connector location for Audi A4 (B9) (2015 – …)
  1. The OBD II socket is located at the left of the pedals.
  2. The OBD port is at the left of the footwell light.
  3. Here is the OBD port.

Where is the OBD port on Audi A4 2017?

Don’t waste your time poking around your car. Just take a look at the video below to see the location of the OBD2 port in your Audi A4.

Where is the battery in the Audi q5?

Is there a fuse for the OBD2 port?

The OBD fuse usually blows for good reason, overloading the circuit. … The OBD fuse may be listed on the fuse cover as OBD II, DLC, Accessory port, 12 v power point or cigarette lighter and will most likely be located inside the vehicle.

What is a VAG scan tool?

VCDS (VAG-COM) is a factory level scan tool that includes support for VW/Audi OBD2 coverage. As a factory tool, it goes beyond the OBD2 standard giving full access to all electronic modules in the vehicle, not just emissions related modules.

How do you reset the service light on an Audi A4?

Start with the ignition turned OFF Press and hold the button on the right side of the display while turning the ignition on (position 2). Service OEL / OIL, should be displayed. Release the button on the right Pull out the button on the left side of the display until the service prompt is cleared.

Why is my obd2 port not communicating?

In most cases, communication issues can be caused by various reasons including: ignition-key position, connector-voltage issues, incorrect communication protocol, hung ECM, missing or bad data, and OEM-updated ECM software that is unknown to the scan tool.

Why is my OBD not connecting?

Check for corrosion or debris in the plug. Check the cable itself for damage, and check the plug at the scanner too. Finding a problem with the plug or cable is easy to fix. Most good scanners will have a detachable and, therefore, replaceable OBD cable.

What is DLC fuse?

The data link connector (DLC) is the multi-pin diagnostic connection port for automobiles, trucks, and motorcycles used to interface a scan tool with the control modules of a given vehicle and access on-board diagnostics and live data streams. … J1708 is a DLC used on heavy duty vehicles.

How do I find my OBD port?

The OBD-II port is usually located under the dashboard, beneath the steering wheel column (1 – 3 in the diagram below). If not located beneath the steering column, look for the port in the areas indicated by numbers 4 – 9. For additional info, check out these Hum FAQs.

How do I connect my OBD port?

Plug the standard OBD2 connector into the vehicle’s port located under the driver’s side of the dashboard. Turn on the car to power the scan tool or code reader. If necessary, enter any vehicle-specific information requested. Many tools will ask for the Vehicle Identification Number (VIN).