Can I light my gas fireplace with a lighter?

Flame-Lit Pilot Light

Turn on the supply line to the gas fireplace. Light a match or butane candle lighter and hold it near the burner in the fireplace. Turn the gas key to release gas to the burner. Pull the match or light away when the burner lights.

How do I light my fireplace lighter?

So lets start the fire!
  1. Ensure that all air vents in the fireplace are open. Put the logs on the bottom of the fireplace. …
  2. Add a layer of small logs of about 4 cm, and then one or two layers of kindling. Remember that air is important – approx. …
  3. Put a couple of firelighters on top of the layer of kindling wood. …
  4. Light it!

How do you light a gas fireplace starter?

How do you light electric gas logs?

How do you light a log fire?

How do you light a heat log?

We find that the best way to light heat logs is to place them on an established fire or on your bed of kindling when you are lighting. Heat Logs burn with a beautiful high flame which is lovely and very aesthetically pleasing, but they don’t put out their maximum heat when they are flaming like this.

How do you light a gas fireplace without an igniter?

Why won’t my gas logs light?

If gas is coming out of the pilot, but it still won’t light, the spark igniter could be the problem. Alleyne says to look for and clear out any debris between the igniter and thermocouple. … The pilot lighting, but not staying lit, indicates that the thermocouple is worn out, Worthen says.

How do you light a gas fireplace with a key and igniter?

How do you manually light gas logs?

Turn the knob from the “Off” to the “Pilot” position. Push in the pilot knob, which manually sends gas into the system. Push the igniter button once every second until it lights. Depending on how long it’s been since the gas fireplace was last used, ignition may take multiple attempts.

Do all gas fireplaces have pilot lights?

It is important to remember that not all gas fireplaces have “standing” pilot light, or, a pilot light that is “always on”. The best way to determine if you have this type of gas fireplace is to look at the control knob of the fireplace. On a fireplace you will normally find the control knob behind the grate or door.

What does the pilot light look like?

A proper pilot flame should be blue with a yellow tip and should be strong enough to cover about 1/2 inch at the end of the thermocouple tip. If the flame is too strong and improperly adjusted, it will be blue but may be noisy and lift off the thermocouple, causing improper furnace operation.

Can I light my gas fireplace without electricity?

Many gas fireplaces will work without electricity. You can run both intermittent pilot ignition fireplaces and standing pilot light systems during a power outage. IPI valve systems will normally have a backup battery system in place to ignite the flames.

How do I light the pilot on my fireplace?

How do you light a pilot light on a lighter?

With the button depressed, hold the lighter flame near the pilot opening. Continue holding the gas valve to the “Pilot” position for at least one minute after relighting the flame. This allows the thermocouple safety sensor to heat up properly.

How do I know if my pilot light is lit?

If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don’t see a flame, your pilot light is out. If there is a flame, check the color. Pilot lights should always be blue.

What color should a gas fireplace pilot light be?

blue
Inspecting a Gas Furnace Pilot Light Flame

A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip. The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip.

Does gas still flow when pilot light goes out?

If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

What can cause a pilot light to go out?

What Causes A Pilot Light To Go Out?
  • Age & Condition Of Heating System. If your gas or propane furnace has a standing pilot light, there’s a good chance that it is 20+ years old. …
  • Cracked Heat Exchanger. …
  • Gas Valve & Gas Supply Issues. …
  • Thermocouple Malfunction. …
  • Improper Venting & Airflow.

How do you light a gas furnace?

How much does it cost to relight a pilot light?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100.

How do you fix a pilot light that keeps going out?

Once The Flame Is Lit, Turn Gas Control Valve to “On”

Once the pilot light is ignited, you can release the reset button after 30 seconds and turn the gas knob to the “On” position. At this time you should hear the main burner come on. Now your pilot light should hold a flame and hot water should be restored!