How do I reset my prestige remote starter?

To reprogram or reset your Prestige car alarm remote, follow these steps:
  1. Start your ignition.
  2. Press and hold the valet/override button for 10 seconds.
  3. When you hear 3 chirps, press the 1 button on the remote.
  4. When the reprogram is accepted, you will see a light flash once.

Where is the valet button on a prestige remote?

Typical locations for valet switch: Under the driver’s side dash (mounted in the under-dash covering trim panel or wire-tied to a harness) Mounted in the driver’s side kick panel. Mounted in the steering column plastic housing.

How do you use a prestige remote starter?

To start the vehicle: Press and release the Key/Trunk button two times within 2 seconds. The vehicle will start and remain running for the pre-programmed 5, 10, 15, 20 minute run cycle. As a visual indication, the parking lights will flash or remain on depending on the setting by your installation center.

How do you program an aftermarket car alarm remote?

How do I know if my car is in valet mode?

  1. Hold down the brake.
  2. Cycle the vehicle key in the ignition between the ‘On’ and ‘Off’ positions 5 times.
  3. Do not touch anything on the remote.
  4. You will know that you have entered valet mode if you see the parking lights flash one time and/or you hear a faint click from within the dash.

How do you program a valet remote start?

1) Open a door and make sure the dome light is on. 2) Turn the ignition on to the RUN position or you may also start car. 3) Within 15 seconds press and release the Valet/Program push button to select the channel you wish to program. For example, press and release once for channel 1 (arm/disarm channel).

How do I reprogram my car remote to my car?

How do you reprogram a car remote?

How to program a key fob
  1. Replace the batteries inside the key fobs. …
  2. Get inside the car. …
  3. Turn on the ignition. …
  4. Press the lock button on the remote key. …
  5. Listen for a Lock Sound. …
  6. Programming additional remotes. …
  7. Turn off the ignition. …
  8. Step out from your car and test the result.

How do I turn on valet mode?

What is valet mode?

Valet mode is a safety convenience feature standard on all Arctic Start remote start and security systems. Valet mode disables all system features other than lock or unlock; such as, remote start, alarm triggers, and trunk release.

Which button is the valet button?

Enable Valet Mode

It is a small, black, momentary button that is usually mounted in an accessible, but not obvious location towards the bottom of the driver’s side dash. A common location would be on the driver’s kick panel cover, or on the side of the center console (if the vehicle has one).

How do I get Astrostart out of valet mode?

What is the override button on a car remote?

: The Override/Programming button is a hidden push button switch that can be used to disarm the security system if your remote control transmitter is lost or stolen. … To prevent unauthorized use of the override/programming button, the ignition key is also needed to disarm the system or program transmitters.

How do you put code alarm in valet mode?

To by-pass the alarm system:
  1. Open the vehicle door. The alarm will sound.
  2. Turn the ignition key to the ON position.
  3. Within 10 seconds, press and release the valet push button switch. The alarm system will stop sounding and enter the (by-passed) mode. You can now start and operate the vehicle normally.

How do I install AstroStart?

Get AstroStart SmartStart in 3 easy steps.
  1. Download the. AstroStart SmartStart App.
  2. Get AstroStart SmartStart Installed in Your Car.
  3. Set Up Your AstroStart SmartStart Account.

How do I turn off my car with AstroStart?

EQUENCE ACTIVATED BY THE PARKING BRAKE .
  1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
  2. Move gearshift lever to neutral.
  3. Apply the parking brake Once Twice. …
  4. Remove key from ignition (the system keeps the engine running).
  5. Exit the vehicle.
  6. Within 60 seconds, close all doors.

How do I reset my alarm code?

Reset user code: Enter the master code and enter *5, then enter the 2-digit number for that. Now type a new user code. Enter your 4-digit code to silence the alarm. Enter your 4-digit code once again and press the “Reset” button to clear the system fault.

What is the valet override button on Code alarm?

The valet button or switch permits the owner to temporarily bypass the alarm functionality of the system. To enter or exit valet mode, disarm the system with a working transmitter, your personalized manual override code, or using the procedure below which is to enter or exit valet mode.

How do you bypass an alarm code?

Bypass a Zone
  1. Enter the following: Your 4-digit code. The number 6 (bypass button) Two-digit zone number of the zone you want to bypass. (01, 02, 03, etc.)
  2. Repeat this process for all zones you would like to bypass.
  3. Once your system is disarmed, this process will need to be repeated in order to arm your system again.