How do you fix a Kenmore washer that won’t drain?

What to Do When Your Washing Machine Won’t Drain
  1. Perform a Master Reset. Unplug your washer for about one minute. …
  2. Test the Lid Switch Assembly. …
  3. See if the Drain Hose is Kinked. …
  4. Check the Drain Hose or Pump for Clogs. …
  5. Clean out the Coin Trap. …
  6. Check the Water Level Control. …
  7. Schedule Washing Machine Repair.

How do you drain a washer with standing water?

5 Easy Steps to Get Water Out of Your Washer
  1. Step 1: Power It Down and Turn Off the Water Supply. Start by powering down your machine. …
  2. Step 2: See If You Can Drain the Drain Hose. …
  3. Step 3: Check Out the Drain Pump. …
  4. Step 4: Drain the Interior Manually If Needed. …
  5. Step 5: Know When to Call a Professional.

How do I get my washing machine to drain manually?

If not, follow these steps:
  1. Step 1: Turn off the power and lay down towels. For safety, unplug the machine. …
  2. Step 2: Locate the drain hose at the back of the washing machine. …
  3. Step 3: Drain the water. …
  4. Step 1: Turn off the power and lay down towels. …
  5. Step 2: Locate the drain hose. …
  6. Step 3: Drain the water. …
  7. Step 4: Scrub the filter.

How do you drain a Kenmore front load washer?

Place a shallow pan in front of the filter door at the bottom of the washer to collect water left in the tub. Open the drain pump filter door, pull out the drain tube and remove the drain tube plug. Allow any water left in the washer to drain into the pan.

How do you position a washing machine drain hose?

In order for the drain hose on your Top Load washer to function properly, the drain must be at least 30″ up from the floor and less than 8 feet high. In order for the drain hose on your Front Load washer to function properly, the drain must be at least 24″ up from the floor and less than 8 feet high.

Should there be water under the drum of my washing machine?

It is supposed to have water underneath the drum; it is only an issue if it backs up into the drum. That water gets changed every time you run the machine. It might be the rubber lining that smells and not the water below the drum.

How do you manually drain a Kenmore washer?

There are multiple ways to drain your Kenmore washer manually, but the simplest way is to remove the drain hose. Locate the drain hose (you’ll find it behind the washer), pinch the pin locking it to the appliance, then slowly pull off the hose. Afterward, the water will pour onto the floor.

Why won’t my Kenmore washer drain or spin?

Where is the drain plug on a Kenmore washer?

How do you reset a Kenmore washing machine?

Most washer’s can be reset like a personal computer. Unplug or turn the circuit breaker off for 30 seconds. Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds. Press the Pause / Cancel / Stop button twice to clear the display.

How do you drain a Kenmore he3 washer?

How do you drain a Kenmore dishwasher?

Why is my Kenmore washer not filling with water?

How do you run a diagnostic on a Kenmore washer?

How do I put it into diagnostic mode? Turn the dial to Drain/Spin, Press Pause/Cancel to turn off the control. Within 5 seconds, press and hold PAUSE/CANCEL and OPTIONS until the LED’s start chasing. Turn the dial one click clockwise to test each of the washer components (water valves, door lock, and motor).

How do I reset my HE washer?

Motor Reset Procedure:
  1. Unplug the washer for 1 minute from the electrical outlet.
  2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
  3. The motor has now been reset and is ready for you to start a cycle.

How do I get my Kenmore washer to fill with water?

Why does my washer not fill up with water?

Why is my washing machine not giving water?