Are Blue Tapcons corrosion resistant?

Tapcon’s unmatched performance in concrete, block and brick applications make them an excellent alternative to expansion anchors, plugs and lag shields. Blue corrosion resistant coating enables them to withstand the harshest conditions.

Are Tapcon screws water resistant?

The 410-grade stainless steel resists corrosion in dry atmospheres, freshwater, acids, mild alkalies, food, hot gasses, and steam. Tapcons are coated with Climaseal®.

Why do my Tapcon screws keep breaking?

The depth of the hole for a Tapcon® should be a minimum of 1/2″ deeper into the base material than the screw will penetrate. … If the Tapcon® screw bottoms out in the hole before it is fully inserted and too much torque is applied, the Tapcon® may break or shear off.

Why are Tapcon screws blue?

Blue Tapcon® Anchors

The blue Climaseal® coating provides extra protection against rust and provides a durable finish that allows for an easy installation. … Technical Information – provides the holding values, product specification, anchor length, anchor spacing and other considerations.

Do Tapcon concrete screws rust?

The Tapcon® concrete screw with the Climaseal® coating gives excellent rust resistance when used for indoor applications and outdoor applications. … The minimum embedment of a Tapcon® concrete screw is 1” and the maximum embedment is 1-3/4”. The threads on the concrete screws are a maximum length of 1-3/4”.

Can you use washers with Tapcons?

Are Tapcon screws any good?

They are also a very unique (and of course proprietary) product that allows for extremely fast and reliable anchoring of materials to masonry products. If you drill the hole correctly – deep enough and with the correct diameter bit – these fasteners will simply work every time.

What size Tapcon do I need for 2×4?

For example, a 2×4 is 1-1/2” thick, so the minimum length of tap con to use would be 1-1/2” + 1” = 2-1/2”. The maximum embedment for all tap con screws is 1-3/4”.

How much weight will a Tapcon screw hold?

*A safety factor of 4:1 or 25% of ultimate pullout/shear value is generally accepted as a safe working load. 340 lbs.

How do I stop my Tapcons from breaking?

The correct setting for driving a tapcon concrete screw without breaking or shearing off is determined by using the lightest setting and then moving up until the tapcon concrete screw is set tight against the fixture being fastened. It is very important that the tapcon is not over torqued.

What are Tapcon screws good for?

The standard blue Climaseal® Tapcon® screw are a light duty masonry anchor primarily used in dry indoor applications for attaching items to concrete, brick or block. They can be used in applications ranging from attaching 2×4 lumber to concrete, a light fixture to brick, or furring strips to a block wall.

Should you use an impact driver for Tapcons?

While there are a lot of ways to fasten to concrete Tapcons are a great light-duty way to do so. They are accessible to most homeowners and DIY’ers because they are easy to use and only require having; a drill with a hammer setting, an impact driver and a masonry drill bit.

How deep should Tapcons be in concrete?

The minimum depth of embedment for the Tapcon screw is 1 inch, and the maximum embedment is 1-3/4 inch. The depth of the hole should be drilled to allow a minimum space at the bottom of the hole of 1/2 inch. The minimum depth of the hole equals 1 inch plus 1/2 inch or 1-1/2” inches.

How long should concrete cure Tapcon?

A full cure takes 28 days if you go by how long they prevented us from driving over a new road surface on a small local bridge. I don’t know how that relates to driving Tapcons. 10-13-2017, 10:37 AM (This post was last modified: 10-13-2017, 12:23 PM by brianwelch.)

Can you use Tapcons on stone?

Can you use epoxy with Tapcon?

For Hanging or Mounting on Concrete, Use Tapcons. … While other systems employ multi-part anchors, or use epoxy that needs time to cure, all you have to do with a Tapcon is drill a hole and screw in the anchor.

How much weight can a 1/4 Tapcon hold?

Technical Specifications for Tapcon Concrete Screws
Size Minimum Embedment Shear (lbs.)
3/16” 1” 400
1/4” 1” 620

Why are my Tapcons not working?

Try getting as much dust out as possible or drill the hole deeper so the dust is below the depth of the length of the tapcon. Drilling deeper for tapcons is not a problem, drilling not deep enough will make the tapcon spin out therefore negating the fastening ability.