What is the standard height for electrical outlets and switches?

48 inches
The standard height for wall switches in most rooms (excluding those over kitchen counters) is 48 inches above the top of the floor covering (measured to the bottom of the box).

How high should light switches be UK?

1200mm
Sockets need to be installed at least 450mm up from the floor level of a room. TV points, telephone points, doorbells and light switches should be a max height of 1200mm from the floor.

What is the NEC code for light switch height?

The only location requirements specified in Article 404 — the section of the NEC that elucidates standards for switch installation — are that switches must be in readily accessible locations and can be no higher above the floor than 6 feet, 7 inches, almost the height of a standard door frame.

Why do electricians install outlets upside down?

Electricians may position the outlet in an upside-down position so that you can quickly identify the switch-controlled receptacle. Since it stands out visually to most people right away – it provides convenience to the occupants to easily remember which outlet is switch controlled.

How far should a light switch be from the door?

There are no national laws on how far a light switch should be from a door frame. It’s recommended that a switch should be installed at least 8 inches from the frame to leave space for the switch plate.

What is the standard height of switch board from floor for residential electrical installation?

A switch shall be installed at any height of 1.3 m above the floor level. Socket-outlets shall be installed either 0.25 or 1.3 m above the floor as desired.

How high should a light switch be off the ground Australia?

Consumer units should be mounted so that the switches are between 1350mm and 1450mm above floor level. At this height, the consumer unit is out of reach of young children yet accessible to other people when standing or sitting.

What height are light switches Ireland?

between 750 and 1200mm
Light switches are provided between 750 and 1200mm above floor level.

Where should light switches go?

Typically, these switches should be placed around four inches above the countertop. Usually, counters reach about 30 inches above the ground, meaning the switch should be placed around 40 inches above the floor. However, the specific height will vary from home to home.

Where should a light switch be placed in a bathroom?

For light switches, plate switches can be used on the inside of the bathroom, but these must be suitable for use in the bathroom, given the high levels of humidity and condensation. And they also must be at least 0.6m away from the bath or shower. A pull cord can be used instead, in any location in the bathroom.

Where should a light switch be placed in a bedroom?

Locating the Switches

By convention, most switch boxes are installed with the bottom of the box located 44 to 46 inches above the floor, this places the top of the box between 47 1/2 and 49 1/2 inches above the floor. By using these conventions, the top of the box is below the maximum 54 inches set down by the ADA.

How far should a light switch be from a sink?

Every bathroom must have at least one electrical outlet. It must be a GFCI, and it must be within 3 feet of the edge of the sink. Either behind or beside the sink is acceptable — across from the sink on an opposite wall is not. If the bathroom has two sinks, each must have an electrical receptacle within 3 feet.

What is a standard light switch?

The single-pole switch is the general-purpose workhorse of switches. It is used to control a light, receptacle, or other device from a single location. … A single-pole switch has two brass-colored screw terminals that are connected to the hot, or power-source, wires. These wires are usually black in color.

How do you rough a light switch?

How far from a shower can a light switch be?

Unless installed as part of a listed tub or shower assembly, switches will not be installed in wet locations. The NEC states that a damp/wet location is within 36 inches of either the edge of a tub sink or basin or an area that is subject to spray.

How close can a light switch be to a toilet?

Every bathroom needs at least one electrical outlet. It must be within 3 feet of the sink edge. Across from the sink on an opposite wall is not acceptable, either behind or beside the sink. There must be an electrical receptacle within 3 feet of the two sinks in the bathroom.

What is the minimum distance between a sink and a socket?

Electrical sockets or switches should be fitted at a safe distance (it is recommended at least 30cm horizontally) from a sink to avoid the chance of water coming into contact with electricity. Sockets should also be easily accessible.

Are light switches allowed in bathrooms?

Light switches are not allowed in bathrooms it has to be a pull cord or a switch outside. Radiator pipes do not have to be bonded IF boiler is cross bonded and/or you have rcd protection on the fuseboard. … Also a isolator for fan outside of bathroom is required.

Why are light switches on the outside of bathrooms?

If a conventional rocker switch is installed, it must be outside the bathroom to avoid risk electrocution. Switches installed inside a bathroom tend to be a pull cord. This prevents contact of wet hands to live electricity, or even dry hands touching a wet switch. Because water and electricity don’t mix!

Do bathrooms need special light switches?

The NEC requires that switches not be installed within the confines of shower and tub areas, unless as part of a shower assembly.

Why are there no plugs in UK bathrooms?

Why are there no plug sockets in British bathrooms? The reason that there are no plus sockets in bathrooms is simple – having an exposed plug socket can increase the risk of electric shock. Plugs in England generally use 240-volt power, twice the amount found in US plugs which have 120-volts.

What is the electrical code for bathrooms?

The NEC requires that all outlet receptacles in a bathroom be GFCI protected. Outlet circuit must be 20 amps: The outlets in a bathroom should be served by a 20-amp circuit, separate from the lighting circuit, to provide power items such as curling irons, razors, and hairdryers.

Do you have to have a pull cord in the bathroom?

It does not need a pull cord unless the switch would be over the sink. If you’re going to leave with wet hands then a switch outside is just as dangerous as inside.

Can you leave shower pull cord on all the time?

You know that pull-cord switch on your shower? Well, leave it alone. … That isolator is only there so the electrical supply to the shower can be locally isolated should maintenance be required. You don’t need to clonk it off every time you hang up the loofah and reach for the towel.