Do hot tubs have a reset button?

A spa heater has a high-limit reset button. A spa or hot tub provides a form of personal relaxation known as hydrotherapy. A spa heater may need to be reset if it has tripped or stopped working. Using the high-limit reset switch and checking all breakers and GFCI outlets can reactivate the spa’s heater.

How do I know if my hot tub circuit board is bad?

If you DO have 220 volts across both hot wires coming from the house, then next measure the voltage across both heating element pins. You should see 220 volts. If you do not, then the circuit board is faulty and will need to be replaced or sent to us for repair.

Where is the high limit reset switch hot tub?

Occasionally, the high limit switch will trip when you’re filling your spa. Or it might need a reset from time to time for no known or serious reason. Simply reset by pressing the big red button on your spa pack. The high limit switch may be housed in a thermowell.

How do I reset my Balboa hot tub?

Spa is shut down for 15 minutes. If water level is normal, make sure all pumps have been primed. Press any button to reset. This message will reset within 15 minutes.

How do I unlock my hot tub control panel?

How do I test my hot tub control panel?

If the problem persists, turn the breaker off and disconnect the panel to examine the circuit board. Turn the power on and check if the hot tub heats up or starts to filter. The surest way to check if a control panel works is to use one you know is working and connect it to the circuit board.

How do you troubleshoot a hot tub circuit board?

If you have no display on your topside control panel, check the cable for damage, following it right to where it plugs in, on the circuit board. Unplug it from the board and the low-speed pump will come on within 1 minute, on both systems. If that doesn’t happen, either the pump or the circuit board is bad.

How do you check a hot tub fuse?

Testing Spa Fuses
  1. Shut off all power to the spa at the breaker and spa pack.
  2. Set your Ohm meter to the 1K setting.
  3. Remove the fuse from the board or fuse housing.
  4. Place your meter leads on each end of the fuse.
  5. Compare readings to printed Ohms level.

How long does a Balboa hot tub last?

How long do Balboa hot tubs last? Hot tub systems made from Balboa Water Group may last from 5 to 20 years depending on how well the hot tub water is maintained and how quickly leaks and maintenance issues are dealt with.

How do I get my hot tub out of sleep mode?

Locate and open the panel with your pool or hot tub pump timer. This should be located close to the pool pump itself and the hot tub. Set the on and off switches to the desired times. Disengage the time dial and set it to the current time.

How do you adjust a Balboa hot tub?

To change the range press the temp/warm button followed by the light button, then press temp/warm button again. To exit, press the light button or wait for 10 seconds to go back to the Main Screen. To check, next to range there is an arrow – if pointing down its in low range, if pointing up its in high range.

How do I make my Balboa hot tub hotter?

To change the set temperature, press a temperature button again before the display stops flashing. Each press of “Warm” or “Cool” will adjust the set temperature. After three seconds, the display will stop flashing and begin to display the current spa temperature.

How do you override a hot tub temperature control?

How do I adjust the temperature on my hot tub?

Most hot tubs today use electronic or digital controls to maintain the water’s temperature. To adjust the thermostat, you simply press the button that increases or decreases the water’s temperature.

Why is my hot tub hotter than setting?

A simple cause of hot tub overheating is the hot tub’s temperature may be set too high. This heat transfers into the tub water, increasing the temperature. So, if the hot tub is set to filter too many hours per day, it can cause overheating.