Why is my Pentair chlorinator not working?

Inspect the check valve: Unscrew the small check valve assembly connected to the base of the chlorinator body. No noise indicates the valve is either clogged or broken and should be replaced or sprayed with a water hose to dislodge any debris stuck in the valve.

How do I know if my Pentair salt cell is bad?

“Check salt” light on power center indicates problem but a routine water sample inspection shows salt levels are fine. Power center’s “Cell warning” light comes on and turns off after a cleaning but back on soon afterward. Voltage (higher than normal) and amperage (usually zero) level will show irregular readings.

Why is my Pentair salt cell not producing chlorine?

High phosphates in the water, a chemical can be purchased at your local pool store or through us to remove higher than normal levels of phosphates. If the water is too cold below 70-65 degrees your chlorinator will not be able to produce chlorine even if your salt level is perfect.

How do I test my salt cell?

What percentage should my salt cell be set at?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

What should I set my salt cell to?

Try to maintain a consistent salt level of between 2,700 parts per million (ppm) and 3,400 ppm, with 3,200 ppm being ideal. Clean the chlorinator cell at least once a season or as needed. During lightning storms, turn off the chlorinator to reduce the risk of power surges that could damage the control board.

Is it OK to run pool pump 24 hours a day?

Although it’s generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. If your pool is in constant use, you may need to run the pump for up to eight hours per day, frequently checking the water clarity and chemical balance.

What should my Intellichlor be set at?

What should the salt level be? The intellichlor is set to function when the salt level is between 2800 ppm and 4500 ppm. Too little, it cannot make chlorine. Too much salt and it also cannot (should not) make chlorine and can cause additional voltage issues with your pool and equipment.

How long should I run my salt chlorinator?

Your pool system including chlorine generator should be operated often enough to completely turn your pool water over at least every 12 hours or twice a day.

Where should I set my chlorinator?

In-line chlorinators must be installed after the filter and after any heater. They should be installed at ground level to prevent back flow, and if you have a heater, a one-way check valve should be installed between the heater and the feeder, to prevent damage from corrosive chlorine gas.

How many chlorine tablets should I put in my chlorinator?

Chlorine Feeders:

For each 5000 gallons of pool water, add one 3″ chlorine tablet, more or less. Choose a mid-point setting on the 1-10 dial.

How do I know if my chlorinator is working?

The easiest way to be certain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights on the chlorinator box. When operating, you should also see bubbles (hypochlorite gas) inside the chamber, producing what looks like cloudy water – that’s chlorine being created!

Can I break 3 inch chlorine tablets?

Don’t break tablets, they are designed to dissolve from a whole tablet, they will overchlorinate your pool if broken up as you have increased the active surface area.

Is it better to put chlorine tablets in skimmer or floater?

You should never add chlorine tablets directly to your skimmer. Purchase an inexpensive floating chlorinator and add your tablets to it. Then allow the chlorine floater to drift around the pool water.

What setting should pool filter be on when vacuuming?

For routine vacuuming, the filter valve is left in the normal “Filter” position. This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water through return lines back to the pool. The “Filter” setting is used for light to moderate levels of pool sediment.

Is it OK to put chlorine tablets in the skimmer?

So if you’ve ever wondered if it’s OK to put chlorine tablets in the skimmer, the answer is yes. As your pool pump runs, water floats in through your skimmer line, past the pump, into the filter, through the heater, and back into the pool.

Should you put chlorine tablets in skimmer basket?