How do you reset the maintenance required light on a Toyota?

How to Reset the Maintenance Required Light?
  1. Turn Your Vehicle on. Your key should be switched to the on position and look on your dashboard.
  2. Turn the Vehicle Off and Press the Trip Meter Reset Button.
  3. Turn the Vehicle Back on.
  4. Keep the Reset Button Pressed.
  5. Release the Reset Button.

How do you turn off the maintenance required light on a Toyota push start?

Push and hold the dashboard odometer button and turn the key to position two. Keep holding the odometer button until the maintenance light starts to flash. You might even hear beeping noises. The light should go out.

How do you reset the maintenance light on a 2014 Toyota?

► Play

How do you reset the maintenance required light on a 2010 Toyota Corolla?

The instructions for the 2010 Corolla apply to earlier models as well.
  1. Turn the ignition switch to the “Off” position.
  2. Press and hold the Trip Odometer Reset button.
  3. Turn the ignition switch to the “On” position. Do not start the engine. Continue to hold down the Trip Odometer Reset button.

How do I turn off the maintenance required light?

How do I reset the “Maint Reqdlight?
  1. Turn ignition switch to the ON position.
  2. Set the Odometer/Trip Display to TRIP A mode.
  3. Turn the ignition switch to the OFF position.
  4. Depress and HOLD the Trip Meter RESET button while turning the ignition switch to the ON position.
  5. The Service Maintenance Reminder Light will.

Why is my maintenance required light on after oil change?

What ‘MAINT REQD‘ Means. TheMAINT REQDlight comes on every 5000 miles from the last time it was reset. It in no way indicates any system malfunction; it is simply a mileage counter intended to remind the user that an oil change is necessary.

How do I reset my maintenance light after oil change?

► Play

How do I reset my oil change light?

Depress the gas pedal slowly three successive times within 10 seconds. At this point, the system should have reset. You can verify by turning the ignition off and then on again. If the light is still on, repeat the process.

Why does the maintenance light come on?

The maintenance required light is notifying you that maintenance is required according to the driven distance on the vehicle’s maintenance schedule. Most often this just means your vehicle might be due for an oil change.

How far can you drive with the maintenance light on?

The light will come on and remain on if the distance driven exceeds 5,000 miles after the maintenance data has been reset.

How do you reset the maintenance light on a Toyota Yaris?

Press and hold the trip meter reset nob (next to your toyota yaris’s odometer). While holding the trip meter reset nob, turn the ignition to ‘on’, but do not start your toyota yaris. Hold the meter reset until the maint reqd light switches off.

What do you do when your maintenance light comes on?

► Play

How do you reset the maintenance light on a Toyota Corolla 2020?

Turn Off Maintenance LightToyota Corolla

Turn the key to the “ON” position, but don’t start the car. Press and hold the trip reset button near the odometer until “Trip A” appears on the central screen. Turn the key back to “OFF.” While pressing the button to reset the trip, turn the key back to the “ON” position.

How do you reset the maintenance required light on a 2020 Toyota Camry?

► Play

How do you reset the maintenance light on a 2015 Toyota Camry?

► Play

How do you reset the maintenance light on a 2014 Toyota Camry with push button start?

► Play

How do you reset the maintenance light on a 2015 Toyota Highlander?

How to Reset the Maintenance Required Light for a Toyota Highlander
  1. Turn the ignition switch to the “On” position but do not crank the engine.
  2. Press the odometer button until the total mileage shows on the display.
  3. Turn the ignition switch off.
  4. Press and hold the odometer button. Turn the ignition on again.

How do you reset the maintenance light on a Toyota Highlander?

Press and hold the “Trip” stem button on the odometer. Continue to hold the “Trip” button while switching the ignition to “On” without starting the engine. For push button ignition models, press the button once. Release the “Trip” button when the trip meter is set to all zeros, and you’re done.

Send us a feedback0/500

Do you like this article?
Yes
No