How do you turn on a Viper remote?

Why does my Viper remote start not work?

A misadjusted or rusted hood pin switch is the most common cause for remote start not working. You may want to consider spraying the hood pin switch periodically with rust-inhibitor to ensure proper operation.

What does the F button do on Viper remote?

Your remote will now automatically lock 60 seconds after your last command is sent. To unlock the remote before each use simply press “F” then the unlock button.

What is the valet button on a Viper remote start?

What is Valet Mode? We all need to let other people operate our vehicle at some point or another. Whether it’s a valet at a restaurant or a mechanic at your local garage. With valet mode, you can disarm your alarm and hand the keys over without the worries of handing over your alarm system.

How do you turn off Viper remote start?

Press and hold the start button on your remote for about three seconds until the lights on the car respond again, signifying that the remote car starter has been turned off and the car is no longer running.

How do I turn on valet mode?

How do I get my remote starter out of valet mode?

To get the system out of valet mode, try pressing the lock and trunk buttons at the same time for 1/2 a second. Problem solved! Many remote starter systems will use a switch to put the system in valet mode.

What is the valet button?

The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions are bypassed, however the remote panic feature and remote door locks will remain operational.

How do I know if my car is in valet mode?

  1. Hold down the brake.
  2. Cycle the vehicle key in the ignition between the ‘On’ and ‘Off’ positions 5 times.
  3. Do not touch anything on the remote.
  4. You will know that you have entered valet mode if you see the parking lights flash one time and/or you hear a faint click from within the dash.

How do you program a valet remote start?

1) Open a door and make sure the dome light is on. 2) Turn the ignition on to the RUN position or you may also start car. 3) Within 15 seconds press and release the Valet/Program push button to select the channel you wish to program. For example, press and release once for channel 1 (arm/disarm channel).

Where is the valet program button?

Typical locations for valet switch: Under the driver’s side dash (mounted in the under-dash covering trim panel or wire-tied to a harness) Mounted in the driver’s side kick panel. Mounted in the steering column plastic housing.

How do I reset my remote car starter?

Press the Lock button on your remote car starter. Within five seconds of turning it on, turn your key back to the “off” position (or press the start button again). Repeat the on-off cycle three more times—you’ll do four in total.

Why does my remote start not work?

If your remote starter system isn’t working properly, try replacing the battery in your fob. You can find replacement key fob batteries at Batteries Plus. Most remote starter fobs run on 2032 lithium coin cell batteries. This one may seem obvious, but if your vehicle is not in “Park” your remote starter will not work.

How do you program a Viper remote without the valet button?

How do you use remote start?

To remote start your vehicle:
  1. Press the Lock button on your key fob to lock all the doors.
  2. Press the Remote Start button (2X) twice. Steps must be done within 3 seconds. The exterior lamps will flash twice and the vehicle will start.

How many times can you remote start your car?

Any vehicle started with the remote engine starter can idle for a total of 20 minutes. Automatic engine shutdown occurs after 10 minutes, but the vehicle may be remotely started as many times as you wish for an additional 10 minutes.

How do you put code alarm in valet mode?

To by-pass the alarm system:
  1. Open the vehicle door. The alarm will sound.
  2. Turn the ignition key to the ON position.
  3. Within 10 seconds, press and release the valet push button switch. The alarm system will stop sounding and enter the (by-passed) mode. You can now start and operate the vehicle normally.