Removing a bathroom faucet can become a really hectic job if not done in a proper manner. And the biggest problem with a faucet is that if we will leave it without removing it then it may cost you a lot. However, it will become an easy thing for you to remove the bathroom faucet if you will follow the below-mentioned instructions carefully. So here are some tips:

  1. Identify the Type of Faucet

First of all, the most important of this process is to identify the type of faucet in order to do further processing. Otherwise, you will find it difficult to gather other tools for the same.

  • There are 3 types of faucet that vary from place to place.
  • The 3 types of the faucet are single hole faucet, 4” triple hole, and 8” triple hole faucet.
  • Once, you are figure out the type of faucet, now try to gather the tools which may be required for the particular type of faucet.
  1. Gather the Required Tools

Replacing a faucet can be an easy job, but it also requires a few tools you will need in order to remove the faucet (old) and install a new one.

  • Adjustable wrench
  • Basin wrench
  • Towel
  • Bucket
  1. Flashlight

A flashlight is very important for undergoing this process.

  • It will help you in getting the desired result in no time.
  • No mishap will happen.
  • You can do the work more efficiently.
  1. Measuring Tape and Plumber’s Tape

A tape will assist you in measuring the length of the pipe which may be required after the removal of the faucet.

  • The tape should be proper in measurement.
  • Make sure that the plumber’s tape is proper.
  • This tape can be used for tying as well.
  1. Sponge and Bathroom Cleaner

While removing the faucet of the bathroom, you may face a lot of difficulties and the place may become untidy, so these tools can help you in order to clean the place.

  • Use it with bare hands and that so very gently.
  • Bathroom soap can also be used to clean the place.
  • The fog of bathroom soap can also be used for the greasing purpose.
  1. Rag or Cloth

A rag or even a cloth can prove to be very helpful while removing a bathroom faucet.

  • It can be used to tighten the hold on the faucet and to avoid the wetness of the faucet.
  • It can also be used for cleaning purposes.
  • But make sure that the rag which you are using is of low quality.
  1. Turn off Supply

First of all, in order to save water, it is pre-requisite to turn off the supply of water.

  • Turn off the supply of water.
  • The valves are at present under the sink.
  • If not, then turn off the supply of water at the valve (main).
  • Thereafter, turn the faucet on in order to relieve any pressure (water) left in lines.
  1. Disconnect Supply

Disconnect the lines of supply from the faucet in order to continue the work.

  • Use a wrench (basin).
  • If you cannot reach given connections with your bare hands.
  • Make sure to disconnect it properly.
  1. Disconnect Lift Rod

Once you have disconnected the supply, it is also very important to disconnect the rod of lift in order to continue the work properly.

  • Once the lift rod is disconnected, move on to the next step.
  • Now, remove all of the nuts from under the bathroom faucet.
  • Make sure that it is entirely disconnected.
  1. Remove the Drain

After you have entirely removed the faucet, now it is time to remove the drain from that spot.

  • On P-trap, unscrew the available slip nut.
  • Put down a bucket which is underneath in order to catch the tap water in your trap.
  • And then remove the drain from the faucet.
  1. Disconnect the Drain

After removing the drain, it is of utmost importance to disconnect the same drain for moving on to the next step.

  • Now, first of all, disconnect the flange (drain) from the present tailpiece.
  • It should be properly unscrewed.
  • And no nut and bolt of that drain should remain there.
  1. Clean it Totally

If you want to smoothen the functioning for the upcoming process then you are supposed to clean each and everything near the faucet. If you will not do the same then the process may become a bit hectic for you.

  • Clean it around the holes of the faucet as well as drain (old one).
  • Thereafter, spirits of the mineral can also help in order to remove the silicone sealant (old).
  • If you will not clean it up properly, then there is a chance that the removal of the faucet will not become possible.
  • When you are cleaning it, be sure that you don’t get any cuts in your hand. You have to scrub the faucet holes if you want to place a new faucet.
  1. Determine the Kind of Faucet that You Have

Once you have completely removed the previous faucet from the holes (mounting), you can now easily figure it out as to what configuration of the hole you are working with and also what kind of faucet you require. So, as already mentioned there are 3 major types of faucets and here is a brief description of the same.

  • Single hole, in which the sink will be having only 1 hole for faucet, and that will all be 1 piece (simple) and that so with a single type of handle.
  • Split-set or Widespread, which actually works with basins of 3-hole, but the spout, as well as 2 handles, come in pieces of 3 separate parts.
  • Center-set, in which there will be a total of 3 holes in the given sink and 1 piece faucet will also have some separate handles which will control the cold and hot water.
  1. Purchase an All-New Faucet

Before you are going to the hardware store for buying a new faucet, determining the type of old faucet is a prerequisite, so have a look at your configuration of basin hole, and thereafter measure the available between both of the holes so that you can get the right replacement of the old faucet.

  • Firstly, write down the total number of holes that your basins have, and also the kind of faucet that was on it.
  • Also, don’t forget to write the correct measurement of the distance between the holes.
  • If you are thinking about replacing your faucet (old) with a new type of faucet, then you will also have to replace the whole basin.
  1. Install Gasket Very Carefully

The gasket is basically a piece of plastic or rubber that completely and tightly sits between the sink and faucet in order to ensure that there is a proper seal and also in order to prevent any leaks.

  • Firstly, fit the gasket properly over the very bottom of the given faucet, by completely matching all of the holes in gasket with valves and tailpipes on its faucet.
  • The gaskets of plastic usually snap easily onto the faucet, so be completely sure while seating them and do it properly such that the faucet is completely seale.
  • If the faucet is not coming only with the help of a gasket, then you will be require to apply the putty of plumber or sealant before you install the faucet.
  • Strictly follow the directions of the manufacturer and then lay down a very thin layer of putty or sealant immediately before you put it in the faucet.
  1. Wrap up All of the Threads with the Tape of a Plumber

The tape of a plumber is designed in such a way that with the help of it you can lubricate the fittings and then create a proper seal in between the components.

  • Wrap all of the ends of the tailpipes of the faucet with a layer of tape of a plumber, but just make sure that the tape that you are using does not in any way extend more than the end of the given pipe.
  • The pipes (tail) will be there where the supply of water hoses and will attach to its faucet.
  • The tape will also help in preventing any further leaks.
  1. Insertion of a New Faucet

Now, it is high time to insert the new faucet available in your hand.

  • Hold the faucet properly in both of your hands and thereafter carefully set it gently into the holes (mounting).
  • Then, match the valves and tailpipes with some very proper holes, and now place your faucet into the very same position.
  • Once you have properly placed the faucet in the holes (mounting), insert a new washer over each of the tailpipes. And thereafter, twist it on the nuts gently by your hands.
  • In order to tighten nuts of it, just turn the nuts in the right direction i.e. clockwise direction.
  • Now, after tightening the nuts by your own hand, finish the job of tightening by turning the nuts another 1/4th turn with a wrench which must be adjustable if it is require.
  • Don’t tighten the nuts more, otherwise, there is a possibility that your sink may get damage because of further tightening.
  1. Attach the Hoses of Supply of Water
  • Begin this step by gently attaching all of the hoses firstly to the faucet. Thereafter, attach each hose to the pipe of the tail of faucet. And now, tighten the fitted nut with the help of your hands.
  • In order to finish the task of tightening the nuts, use the wrench of the basin for turning each of the nuts only a quarter turn to its right side i.e. in a clockwise direction.
  • Once all of the hoses are properly attached to the all-new faucet, reattach all of the hoses to the supply of water. Then, turn all of the nuts by your hand to clockwise direction i.e. right side. And then again tighten the nuts with the help of an adjustable wrench for the remaining of the way.
  • In case, you are attaching the lines of supply to the pipes of copper and that so with the fittings which are threaded, then hold the pipe of copper very securely while you are connecting the lines of supply in order to ensure that the pipes do not break or twist.
  1. Turn on Water

Once you have attached and fixed each and everything, now it is time to check whether you have done the work properly or not. So, just turn on the water.

  • Make sure that you have enough water in your tank.
  • The water that you are using should be clean.
  • No tangible objects should be there in the water.
  1. Test the Faucet

When all of the things are tightened and connected, turn the water on to test the faucet.

  • Turn the taps on in order to flush out or check the new faucet that you have installed.
  • When the water has started running, just check for drips and leaks.
  • For flushing the faucet, just let the cold and hot water run for around 1 to 2 minutes.

TIPS

  • When you are removing the faucet of the bathroom, don’t forget to turn off the supply of water.
  • While removing the faucet of your sink, put your hand gloves on to avoid any injury; just as a precaution.
  • If you don’t want to get into trouble very early regarding the faucet, then make sure that you are buying a new faucet which is of good quality.

How do you remove a 3 hole bathroom faucet?

How hard is it to replace a bathroom faucet?

Replacing a leaky or outdated faucet isn’t as difficult as you might think. You can tackle the project with a basin wrench and a few other common tools. It should usually take no more than about an hour.

How do you loosen the nut under the sink faucet?

How do you remove a stubborn nut?

How do you remove a hard bathroom faucet?

Can’t get bathroom faucet handle off?

If it’s stuck, wrap a rag around it, give it a few light taps with a hammer and try again. Squirt a few drops of penetrating oil or spray lubricant into the space between the handle and the valve stem. Wait a few minutes, then tap the handle and try pulling it off. Place a scrap piece of wood on the faucet body.

How do I remove a Moen widespread bathroom faucet?

To remove the cartridge from your widespread faucet assembly, first hold the handle steady and unscrew the handle hubs counterclockwise. Once the handle hubs are loosened completely, pull the handles off the valve assembly. Then, using tool #14272 (which is not included), loosen and remove the cartridge nut.

How do you remove a screwless faucet handle?

Once you find the necessary tools, you’ll need to follow these steps to remove the screwless faucet handle successfully.
  1. Step 1: Turn off the water.
  2. Step 2: Remove the cap on top of your faucet.
  3. Step 3: Remove the hidden set crew.
  4. Step 4: Remove the faucet handle.
  5. Step 5: Rinse off mineral deposits.

How do you remove a delta bathroom faucet handle?

How do you remove a single handle bathroom faucet?

Single–Handle Bathroom Sink Faucets – Handle Removal
  1. Using a bladed screwdriver, gently pry off the plug button under the handle, taking care to protect all finished surfaces.
  2. Using a 1/8″ hex wrench, loosen the setscrew securing the handle to the valve stem.
  3. Lift off the handle.
  4. Unthread the bonnet to expose the valve.

How do you remove a single faucet handle?

Removing a Single-Lever Faucet
  1. Step 1: Turn off Main Water Valve. Before even starting to remove the single lever faucet, make sure you turn off the main valve of your water.
  2. Step 2: Detach the Handle.
  3. Step 3: Remove the Valve Screw.
  4. Step 4: Undo the Faucet Screws.
  5. Step 5: Remove the Metal Ring.
  6. Step 6: Remove the Faucet.

How do you remove a Moen single handle faucet?

Some Moen faucets have handles that remove by loosening the screw in the back of the handle. To loosen this screw use a 3/32″ hex wrench. After the handle has been removed unscrew the spout collar nut by turning counterclockwise then lift and rotate the spout.

How do I take apart a faucet?

How do I remove a faucet cartridge?

How do you take apart a faucet head?

How do you remove a sink faucet?

How do you remove a faucet without a basin wrench?

How To Remove Kitchen Faucet Without Basin Wrench |SOLVED|
  1. Turn off valves to prevent a mess.
  2. Open the faucet to relieve pressure.
  3. Disconnect water lines to clear faucet.
  4. Remove kitchen faucet nut.
  5. Disconnect the hose to complete the job.
  6. Reconnect the faucet.

How do you remove a bottom mount faucet?

Using a basin wrench, reach up behind the sink basin from inside the vanity cabinet and grip the mounting nut that holds one of the faucet valve tailpieces to the sink or countertop. Turn the nut counterclockwise (viewed as you look upward at the nut from below) to loosen it, and unscrew it down the threaded tailpiece.