Why isn’t a 2×4 actually 2×4?

DIMENSIONAL LUMBER: In the past, when a timber was called a 2×4 [or “two-by-four”], it actually measured 2 inches by 4 inches. … Because of this extra milling, a 2×4 no longer measures a full 2 inches by four inches. Instead, a 2×4 is really only 1 1/2″ by 3 1/2″.

Why is a 2×4 only 1.5×3 5?

The 2×4 refers to the rough-cut green wood: it shrinks during drying, then the dried wood is planed smooth, so the finished lumber is supposed to end up at 1.5″x3. 5″. While it doesn’t really shrink that much, the mills get more usable finished 2×4’s from a given tree if they cut them slightly smaller to begin with.

Why is lumber sized the way it is?

Lumber sized according to “Quarters” reflects the number of quarters of an inch thick the lumber is. … So, a “4/4” board is four quarters, or 1 inch thick, an “8/4” board is eight quarters, or 2 inches thick, a “10/4” board is ten quarters, or 2.5 inches thick, etc.

Why is lumber smaller than the size it says?

Typically, that rough cut is smaller than the nominal dimensions because modern technology makes it possible to use the logs more efficiently. For example, a “2×4” board historically started out as a green, rough board actually 2 by 4 inches (51 mm × 102 mm).

What do they call a 2×4 in Europe?

I cant speak for the hole of europe, but at least in Norway a “2×4″ is 48×98 mm. If you go to a lumberyard, you buy 48×98 as everything is measured in metric, but in the daily speach most people still use the term 2×4, 2×8 aso. The Inch measurement is in use as long as we speak about size on TV(40″) and cartyres (15”).

When did they stop making true 2×4?

This pressured further compromise because thinner 2x4s were a way to compete in price with wood alternatives. Size standards, maximum moisture content, and nomenclature were agreed upon only as recently as 1964. The nominal 2×4 thus became the actual 1½ x 3½, imperceptibly, a fraction of an inch at a time.

Why are wood dimensions wrong?

The “nominal” cross-section dimensions of a piece of lumber, such as 2 X 4 or 1 X 6, are always somewhat larger than the actual, or dressed, dimensions. The reason is that dressed lumber has been surfaced or planed smooth on four sides (called S4S). The nominal measurement is made before the lumber is surfaced.

What is the difference between actual and nominal?

Nominal size is the size you see printed on the side of your air filter. It stems from the actual size, which is rounded up to the nearest whole inch.

Why are boards a half inch short?

Through the drying process, the boards naturally shrink, as moisture leaves the beams. … Without the rough edges, what went in as a 2-by-4 planks of rough-sawn wood is now a tongue-tripping 1.5-by-3.5, having lost approximately ¼-inch on all sides to the planer and drying processes.

When did lumber dimensions change from actual to nominal?

Early concepts called for rough lumber to be of full nominal size, often in the dry condition. After World War I, the increasing demand for construction lumber led to the first national size standard in 1924. This was revised in 1926, 1928, 1939, and 1953, while still another revision is proposed for adoption in 1964.

What is the difference between nominal and actual size of wood?

The nominal measurements are a board’s size before it has been planed smooth (surfaced) on all 4 sides. The actual measurements are the final size. If your project calls for precise measurements, be sure to check your lumber before purchasing.

Are lumber lengths accurate?

You’ve just run into the reality of actual lumber sizes as compared to the nominal sizes—the sizes by which they are identified in the store. The measurements by which lumber is sold is virtually never the same as the actual dimensions of the boards when you measure them.

Why is nominal board size different than actual board size?

The nominal measurement is given to the lumber when it is sawn according to the size it is then. Drying and planing decrease the size making either type of actual measurement different than the nominal size.

What is the difference between nominal and rough lumber?

Rough sawn lumber has a very rustic appearance, which is a desirable look for some projects. … After it is planed, the piece of lumber no longer has its nominal dimensions, for it has been reduced in size. It is stilled referred to by its nominal size, such as the 2×4, but its actual size is now 1 1/2” by 3 1/2″.

Why is a 4×4 actually 3.5×3 5?

no, it is just a bit over 3.5″x3. 5″ for clearance. 2×4 and 4×4 boards are no longer the actual number, but as you state–they are 1/2″ LESS. the base fits nicely to a standard 4×4.

Can you buy actual size lumber?

Actual Lumber Sizes Actual size is as actual and real as if you were using a tape measure or a straight edge to measure the dimensions of the stock. Actual size is anywhere from 1/4 inch to 3/4 inch less than nominal size.

What is the difference between true size and actual size?

The actual size refers to the exact measurements of your air filter, and the true dimensions when you measure the length, width, and depth (thickness). Actual size typically includes a fraction number within the dimensions – for example: 19 1/2″ x 19 1/2″ x 3/4″.

Why do 2×4’s have rounded edges?

2×4 have rounded edges as it’s very beneficial to the wood itself and those working with it. They reduce the number of injuries like unwanted splinters during the handling and manufacturing process and also ensure that the lumber stays looking its best all throughout until the customer sees it.