How do you take the back off a Hotpoint tumble dryer?

How do I take the back off my dryer?

Use a nut driver or screwdriver to remove the screws that secure the back of the dryer to the dryer cabinet. If necessary, insert a flathead screwdriver between the back panel and side of the dryer cabinet to separate the back panel. The back panel can become sealed to the dryer due to heat, humidity and lint.

How do you disassemble a Hotpoint dryer?

How do you take the top off a Hotpoint tumble dryer?

How do you disassemble a tumble dryer?

For some dryers, you’ll need to remove screws at the top of the back panel.
  1. Remove the screws from beneath the lint trap. …
  2. Use a putty knife to release the clips that secure the top. …
  3. Once you release the dryer’s top, you can lift it off. …
  4. Disassemble the lower kick plate panel. …
  5. Support the drum and remove the front panel.

Where is the heating element located on a Hotpoint dryer?

Locate the heating element cabinet on your Hotpoint dryer. This is usually on the back of the dryer, but some models may have it in the front instead. Loosen any screws or clips securing the compartment panel, and remove the panel to access the heating element.

How do you disassemble a Hotpoint dryer?

How do you open a Hotpoint dryer?

Use your screwdriver to remove all screws that hold the lid in place.
  1. Open the dryer lid. On a new-style Hotpoint dryer, you do this by flipping open the hinged lid. …
  2. Slide the front panel off. …
  3. On newer Hotpoint dryers, you get a better view from the side by pushing the cabinet’s side panels.

Why is my Hotpoint dryer not heating?

If your dryer isn’t heating up, or is blowing cold air, it’s probably down to either the heating element or the thermostats. … And a safety thermostat, this will open if the temperature gets too hot to prevent damage but will not reset when cold. The other cause of a cold dryer is a faulty element.

Why isn’t my Hotpoint dryer heating?

Common solutions for: Hotpoint Dryer not heating. The thermal fuse is a safety device designed to protect the dryer from overheating. … Be aware that a blown thermal fuse is an indication of a restricted exhaust vent from the dryer to the outside. Always check the dryer venting when replacing a blown thermal fuse.

Where is the thermal fuse on my Hotpoint dryer?

The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good.

Why is my dryer blowing cold?

One of the most common reasons your tumble dryer decides to blow out cold air instead of hot is, rather ironically, because it has overheated. … If your tumble dryer does not have a reset button it is likely you will need to replace your thermostat and thermal overload cut-out (TOC).

Why is my Hotpoint tumble dryer not drying?

We recommend the following: Ensure that the vent hose is not blocked or crushed. Ensure that your Hotpoint tumble dryer is not being overfilled with clothing as this will impair the performance. Double check the heat switch on your dryer is set to the appropriate position.

How much does a heating element cost for a Hotpoint dryer?

How Much Does a Heating Element Cost for a Dryer? A new heating element is usually between $40 and $100.

Where is the dryer reset button?

Often, dryers are equipped with a reset button on the control panel.

What do you do when your dryer won’t heat up?

This is the most common cause of a dryer not heating. To check if your venting is clogged, start a timed dry on high heat. Go to the exhaust vent outside and use your hand to verify that the air is very warm and exiting at a decent flow. If there’s little airflow, your venting likely needs to be cleaned or replaced.

Why is my dryer running but not heating?

Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element.