Is it hard to apply Cerakote?

APPLICATION. The steps are relatively simple: disassembly, sandblasting, cleaning, painting, and baking. But, of course, simple doesn’t mean easy. Cerakote is ridiculously thin.

How does Cerakote get applied?

Each part is sprayed via Cerakote’s rigorous standards using equipment and technique specified by Cerakote. After the Cerakote coating is applied the parts are taken to our baking oven to bake out to Cerakote Standards. … The parts are then inspected for proper coating thickness, look, and feel.

Can I Cerakote myself?

However, should you decide to do the work yourself, there are two formulas of Cerakote: oven-cured and air cured. The former requires baking in an oven, the latter cures in the air. … If you decide to apply the finish yourself, it is highly recommended that you DO NOT use your kitchen oven.

What can Cerakote be applied to?

Cerakote is a specialized coating that can be applied to wood, polymers, metals, and plastics that is composed of a polymer-ceramic compound. The ceramic coating benefits the firearm by providing and enhancing physical components including: Improving the wear and tear over time.

Does Cerakote scratch easily?

Cerakote® is a ceramic polymer based proprietary formulation that offers industry-leading durability, hardness, scratch resistance, corrosion resistance, flexibility, heat, and chemical resistance.

Does Cerakote have to be baked?

Recommended Cure Temperatures

Cerakote can be cured at the maximum Recommended Cure Temperature listed in the All in one TDS, based on color and substrate. Standardized curing temperature for H-Series is done at 250°F for 2 hours following a 15 minute ambient flash time.

Is Cerakote permanent?

Cerakote requires many hours of prep, spray, and cure time before the firearm can be used. It is a permanent application that cannot be reversed so easily but will endure a long time.

Can you Cerakote over wood?

Cerakote is a ceramic based finish that can be applied to metals, plastics, polymers and wood.

Which is better powder coat or Cerakote?

Traditionally, Powder Coat has been known as the go-to coating solution for automotive components, however, as of recent, many fab shops and individuals have discovered and transitioned to Cerakote. Cerakote is compatible with more automotive components thanks to its ultra-thin finish and high-temp tolerance.

Can you use gun oil on Cerakote?

If you have a firearm completely refinished in Cerakote or Duracoat, a period of 200 to 300 rounds is typically required for break in with quality gun oil or grease. After this period you can run your weapon lightly lubricated!

Does Cerakote chip?

Is Cerakote really durable? Absolutely. It won’t chip, flake or scratch off. Tests have shown it more durable than traditional bluing, parkerizing or other finishes.

Does the military use Cerakote?

Red Creek Tactical Cerakote

Cerakote is one of the toughest coatings you can put on a firearm. It is currently used on a number of production pistols as well as many custom firearms. Military and law enforcement versions even have protection against IR detections.

Will brake cleaner remove Cerakote?

Firearm cleaners or lubricants will not hurt the Cerakote finish. You can even use acetone or brake cleaner!

Is acetone safe on Cerakote?

Acetone will not harm a fully cured Cerakote finish.

Is Cerakote oil resistant?

Did we mention that its super easy to clean as well? Parts coated in Cerakote are not only highly resistant to chemical it is also highly resistant to friction and improves the functionality of lubricants.

What cleans Cerakote?

After Straining Cerakote into your spray gun, you will want to have a waste bucket, acetone, and lint free towels ready for cleaning mesh strainer. Begin by flushing acetone through bottom side of strainer to wash out any trapped particles. Clean the opposite side of the strainer using the same method until clean.

Is Cerakote solvent resistant?

About Cerakote

Chemical Resistance testing showed that Cerakote was rated as excellent in 14 solvent tests. Those solvents included denatured alcohol, lacquer thinner, acetone, gasoline and paint stripper.

Can you use brake cleaner to clean firearms?

Can you Cerakote with an airbrush?

The Iwata Eclipse HP CS is the go to “artistic” airbrush. … This airbrush can achieve fine details even with thicker products such as DuraCoat and Cerakote.

Whats better than Cerakote?

GunKote is the biggest competition for Cerakote; each have their own following for being “the best” firearm coating, and both are comparable when tested against corrosion, chemicals, and durability. KG Gunkote also has two series, the 2400 Series (Oven Cure), and the 1200 Air Cure Series.

Is Cerakote a PVD?

Cerakote ceramic coatings are a premium upgrade and an excellent alternative to PVD (Physical Vapor Deposition), Ionbond, and DLC coating (diamond-like carbon coating).