【How-to】How to attach ledger board to house

How do you attach a ledger board to a house with siding?

Attaching a Ledger Board to Your House

Remove Siding. Determine the outside dimensions of the framing for the deck and add ½” to 1″ to that length. …
Important. …
Set the Height of the Ledger Board. …
Block Joists from Inside the House. …
Install First Flashing Piece. …
Bolt Ledger in Place. …
Install Second Flashing. …
Attach Joist Hangers.

How many lag bolts do you put in a ledger board?

Approved Fasteners

The International Residential Code lists two fasteners for directly attaching ledgers to a house: 1/2-inch-diameter hot-dip-galvanized hex-head machine bolts and 1/2-inch-diameter hot-dip-galvanized lag screws. Note that “carriage,” or “cap head,” bolts are not listed.

Can you attach a ledger board to siding?

In order to install the ledger board, you usually need to remove the house’s siding. Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection. … Set the blade depth so you won’t cut into the house sheathing below the siding.

Can I attach a ledger board to wall studs?

MiTek’s WSWH Washer Head Structural Wood Screw can be used to attach a ledger to studs directly, through 1/2″ APA rated sheathing or through one or two layers of 5/8″ gypsum wallboard (drywall).

Can you use Tapcons for ledger board?

It probably did not equate to us getting many new products but there was a lot of good information regarding fasteners and joist hangers. Titen HD anchors (Tapcons on organic compounds as some call them) even in galvanized finish are not to be used in exterior application. Never to be used to attach Ledger Boards.

How do you attach a ledger board to a house for a patio cover?

Attach the ledger with 1/2-inch-diameter lag screws or bolts every 16 inches (or as specified by local building codes). Slip stainless-steel washers between the ledger and the siding to allow water to flow behind the ledger. If you can’t get behind the joist to cinch down nuts, use lag screws.

How do you attach a ledger board to a wall?

Use a wood bit to drill ½” pilot holes through the ledger board. Next, use a concrete bit to drill into the concrete wall. Install two bolts at the end of each ledger board. Hammer the sleeve anchor through the ledger board into the concrete wall.

How do you attach a ledger board to drywall?

First, use a large ledger with multiple lag screws. Drill pilot holes for the lags through the ledger into the stud (says anyt lag over 1/4″ needs a pilot hole. Then, use the pilot hole to bore a 1″ or so hole through the drywall. Insert washers flushwith the drywall, bore the ledger and install the lag screws.

How much weight can a ledger board hold?

The ledger is 10′ long so every foot of ledger must be designed to carry at least 200 lbs of load.

How do you attach a ledger board to a house for a pergola?

How do you attach a hollow block to a ledger board?

When attaching a ledger to hollow masonry block, use adhesive anchors, such as the Epcon A7 from ITW Red Head (800/348-3231, www.itw-redhead.com) or the Hilti HIT HY 20 system (866/445-8827, www.us.hilti.com).

Is it safe to attach pergola to house?

No matter where you’re putting the pergola, keep in mind that, generally. you’ll be omitting two of the posts in this project, so stability is your number one concern. This means that the pergola’s connection to your home must be extremely strong, or it could damage the walls of your home.

Do I need planning permission for a pergola attached to my house?

You will need planning permission for your pergola if it’s on the front of your house. You will need planning permission for your pergola if it is in a conservation area, on the side of your house between the house and the boundary wall. … Any sort of veranda, balcony or raised platform will need planning permission.

How do you make a pergola attached?

How do you attach a pergola to the roof of a house?

How do you anchor a pergola without drilling?

Using leg weights is the best option for securing your gazebo without drilling into the ground. Gazebo leg weights work on any surface and can easily be filled with either water or sand. They are also capable of holding down your gazebo without fear of it getting blown away.

Will pergola make house dark?

Will a Pergola make a house dark? When built next to your house, whether freestanding or attached, the Pergola can have knock-on effects. The key purpose of a Pergola is to offer shade but if it is constructed outside of a window this may result in the room feeling too dark.

Can I attach a ledger board to a fascia?

If you own a two-story home, you can tie the ledger into a band joist. Find the band joist by measuring down from the 2nd story window. When you attach the ledger boards to the fascia, they should be held securely with bolts through the wall, or you can use lag screws.

How do you attach a patio roof to the side of a house?

How do you attach a ledger board to a second story deck?

Can I attach pergola to fascia?

Building a pergola that attaches to an existing home usually requires that it be tied in to the fascia. A fascia board alone is usually not of sufficient strength for this attachment, and a proper attachment must be to the header and roof rafters. Allow to dry for 24 hours.