It becomes hard for us when our daily use machines go down, and we get stuck in between the list of mechanics and service centers, which don’t really seem to be a good idea to persuade.

Therefore, here comes some handy ways of repairing your washing machine, which saves you from further delays and monetary wastage.

  1. In Case the Washing Machine does not Start

After putting up all the clothes, power plug in and machine’s power on, if the machine does not respond at all, even the light button on the machine seems to be dim this can be an issue with the power or machine’s lid.

  • Make sure the washing machine’s plug is plugged in the switchboard well. In a case when the washing machine vigorously moves, the wire may get stretched or the plug of the machine may have damaged.
  • Check if the circuit breaker of the washer is not faulty. In case the circuit breaker proves out to be faulty, find the electrical service panel and reset it. Look for the correct circuit breaker; put it off and on again.
  • In case you have a front load washing machine, check for the door lid. Since the washing machine never goes on unless the door is abstractly closed. Look for the door lid getting perfectly closed; I.e. the part on the door gets perfectly attached to the part on the washing machine.
  • And in case you own a top load washing machine, you can still look for the same problem with the top door. In case the part on the door on the machine is broken, try to fix it to make the door closed subsequently.
  1. The Washing Machine is not Adequately Cleaning the Clothes

This can be a frustrating issue with it, that the machine looks perfectly fine but has a basic defect of unsatisfied cleaning. To avoid such problems, make sure the following:

  • You don’t overload the machine with too many clothes. Since a few people put on too many clothes in the machine to save electricity and time, face this. When overcrowded clothes get less space to spin and the water and detergent don’t get enough scope and area to pull out the oil and dirt, the clothes don’t get clean enough.
  • Avoid the use of excessive detergent, because the use of too much of the soap and powder can possibly resettle on the back of the clothes because the water gets unable to dissolve all of the powder.
  • Avoid putting up pet clothes along with the rest of your clothes. Since the pet items seem out to be extremely dirty, they can affect the rest of the clothing too.
  1. Washing Machine’s Spin Defect

This is the most common problem in washing machines, that the basin drains the water but refuses to spin. It is necessary for the spinner to spin and squeeze out the water to get dried.

  • Try rearranging the clothes in the washing tub. This is because, when the spinner gets imbalanced with load, it automatically stops working. Open the lid, redistribute the clothes, and close it again.
  • Do check the machine’s level from the floor. In case the level is improper, the machine’s spinner may have trouble starting. This action is programmed by default for the washer’s safety. Do adjust the machine legs and bring it back the level suggested.
  • Any clog in the machine’s hose may also put the spinning of the spinner down. Check the washer’s drain pump for any luggage. Check the drainer and drain hose and try removing any clog that you may find.
  1. Washing Machine Making Loud Noises

If you notice thumping, thunking and grinding noises while agitation and spinning, this may be really irritating at times. This can be a crucial problem and it should be solved immediately since too much of its erring movement can harm the washer and create new issues.

  • The tub bearings, at the lower side of the tub, may be damaged and would be in need of replacement.
  • If you hear squeaking sound out of the washing machine, the machine would be in need of some lubricant and lubrication in the tub bearings.
  • Another possibility is that the motor drive belt or machine pulley would have depreciated or damaged.
  • Also, the pump pulley belt could also have been cracked or bent. The belt may also smell like burning rubber. Do get that repaired or changed.
  1. The Machine is not Agitating

This is one of the common problems with machines. Even after filling the tub with water, the central agitator does not work.

  • Agitation is the back and forth motion of the machine which assists in cleaning of the clothes. This is done by the tall vertical spindles, vaned or finned devices, in the center of the washer called the agitator. Do open the cover of the machine amid agitation mode. Lower the cover switch with the blunt end of a pen so that the machine does not halt while the cover is open. If the machine is creating usual sounds of agitation or any thumping commotion, yet the agitator is not working, the cogs may be broken or damaged and in need to be replaced.
  • The machine’s washer motor could have been influenced badly by power hype and should be reset. Different brands have distinctive reset techniques; check the owner’s guide for potential info and procedure and also about motor resetting. For example, if you have General Electric washing machine, it will need you to remove the plug of the machine, plug it back in, then raising and lowering the lid six times within 12 seconds, lifting the lid an average of two inches as to break the lid switch magnetic association.
  1. In Case the Washing Machine does not Drain Water

In case you have got an unpleasant experience of discovering floating clothes in a tub with dirty grey water.

  • It might be possible that the pump is clogged with fabric or some other item. Take the water out and then unplug the washing machine. Now you need to remove the screws on the head panel. Hold the machine up, tilt it and balance it by some short stool. Then you might be able to see the machine’s pump. You may make use of pliers to lightly uncoil the clutter from the machine’s pump.
  • It also might be possible that the clog could be existential in the corrugated tube which connects to the pump. Unclamp the tube and take the water out in some bucket. Drain out the water, and if there would be some clog in the hose, it will be generally at the ending of the pipe. Take it out using some pliers or your hand.
  1. Excessive Vibration and Shaking of the Washing Machine

There is a high possibility that the machine needs to get rebalanced. The bubble level can be used to evaluate the level of the machine sidewise and front or back. You need to readjust the level of the machine by relocating the machine’s legs upside and downside.

  • There is a high possibility for the connection straps to have been loosened, making the washing machine to shake vigorously. Do open and tighten the connection straps or buy and replace them if they’re broken or damaged.
  • You also need to focus on the load of the clothes you offer to the machine. In case of washing blankets, sweaters or anything heavy, you should reduce the weight of another burden so that the machine could work upright or else the machine will be facing a major problem in the agitator.
  • You might be required to purchase an anti-vibration pad. Three inches thick pads do a brilliant job of ending shaking and vibration. These pads can reluctantly increase the life of your washing machine; hence they make themselves worthy of being bought.
  1. Leaking Washing Machine

Many domestic houses face the problem of leaking washing machines which tend to create a slippery and wet floor around and also a problem while washing clothes.

  • Do check the fittings well, the hoses connected to the faucets and to the back of the washing machine might be loose or defaulted. You should also try tightening the couplings or hose clamps. Make sure you stop the water flow before you remove the hoses. Drain the water into a bucket after disconnecting them.
  • Make sure you check the seals and bearings. The machine might possibly have a faulty basket or tub seal and bearing, which is required to be replaced. In the case of damaged tub seal or bearing, you’re suggested to call an appliance repair person because doing it on your own without technical knowledge may increase the burden of the problems.
  1. Washer Smells

Sometimes the washer in your washing machine begins to smell which can turn out to be a crucial problem lately.

  • It is very common for a washer to develop a foul smell. This can occur into the appliance and around it. It is a clear indication of bacterial growth and mold. The washer comes with a dark, moist area for bacteria.
  • Every washer develops “biofilm” which is basically a decaying matter. Some washers are a bit more prone to such growth. If the smell is not treated, it can start affecting your laundry and nearby rooms.
  • To overcome this, you can eventually develop a good habit to clean your washing machine on monthly basis. Also, you can periodically check the area near the washer for bacterial growth and mold. If the other areas start to show signs of mold, there might also be a possible issue of moisture that needs to be addressed on time.

TIPS

Above mentioned were some of the commonly faced problems in the washing machines, and below mentioned were some of the common techniques that could be used for the repairing and maintenance of the same according to domestic approach.

Source:

14 views